how to change cleats on cycling shoes

How to Change Cleats on Cycling Shoes: Quick & Easy Guide

By Laura Rodriguez
AD

Mastering how to change cleats on cycling shoes is one of the most essential maintenance skills for any cyclist, whether you commute daily or race on weekends. Over time, the rubber teeth on your pedals wear down, and the fixed positioning of the cleat can develop hot spots on your shoes, making this adjustment crucial for comfort and power transfer. This guide walks you through the entire process, from gathering the right tools to setting up your new float for a perfect ride.

Why Replacing Cleats is Essential for Performance

Worn cleats lose their grip, leading to a disconnect between your foot and the pedal that can sap efficiency and create instability during your stroke. Beyond safety, old rubber can cause uneven pressure on your metatarsals, turning a minor nuisance into a painful hotspot or even a foot injury. By learning how to change cleats on cycling shoes now, you ensure optimal power transmission and protect your joints from misalignment. Most professionals recommend inspecting your cleats every 3,000 to 5,000 kilometers or immediately if you notice slipping or audible squeaking.

Tools and Materials You Will Need

Before diving in, ensure your workstation is prepared with the correct equipment to avoid stripping bolts or damaging the carbon fiber on your soles. The right tools make the difference between a five-minute swap and a frustrating struggle that could damage your expensive gear.

AD
How-To Install Cleats on Cycling Shoes The RIGHT WAY! | Clipless Pedal DIY for Shimano SPD and More.
How-To Install Cleats on Cycling Shoes The RIGHT WAY! | Clipless Pedal DIY for Shimano SPD and More.
Cleat position explained: how to setup & replace cycling cleats | BikeRadar
Cleat position explained: how to setup & replace cycling cleats | BikeRadar
a person holding a red shoe with two holes in it
a person holding a red shoe with two holes in it
  • Compatible replacement cleats (check your brand and model)
  • Hex key set (usually 4mm, 5mm, or 6mm)
  • Torque wrench (highly recommended for carbon soles)
  • Soft jaw claw hammer or rubber mallet
  • Pedal wrench or 15mm spanner
  • Small screwdriver or pick for debris

Step-by-Step Removal of Old Hardware

Start by unclipping the shoe from the pedal and placing it securely on a stand or with the sole facing upward. If you cannot see the bolts clearly, use the small screwdriver to push debris out of the recessed holes. Position your hex key into the bolt and turn counter-clockwise; if the bolt is stiff, gently tapping the end of the key with a hammer can break the rust without applying excessive force. Carefully remove the bolts and keep them in a safe place to avoid losing the washers, which are often critical for maintaining proper tension.

Checking the Sole for Residue

Once the old hardware is out, inspect the sole for remaining adhesive or broken plastic threads. If you are installing the same model of cleat, you might notice that the positioning holes are slightly offset; this is intentional to allow fore/aft adjustments. Use your pick to clean out any gunk, as leftover residue will prevent the new bolt from seating correctly and could lead to a loose cleat mid-ride.

How To Install SPD Cleats on Bike Shoes?
How To Install SPD Cleats on Bike Shoes?
How To Set Up Cleats For Clipless Pedals
How To Set Up Cleats For Clipless Pedals
Cycling cleats: how to set up cleats on cycling shoes • Q36.5
Cycling cleats: how to set up cleats on cycling shoes • Q36.5

Installing the New Cleats Correctly

Take a moment to compare the new cleat with the old one; they should match in width and the curve of the floating track. Apply the recommended torque specification gently—over-tightening is a common mistake that cracks carbon soles, while under-tightening leads to dangerous float. Align the holes precisely and thread the bolts by hand first to avoid cross-threading, which is a quick way to ruin expensive shoes.

Setting the Float and Tension

Before you secure the hardware completely, check the float of the cleat. Most modern pedals allow side-to-side movement, and the cleat must match that range. Tighten the bolts in a diagonal pattern, similar to tightening a car wheel, to distribute pressure evenly across the sole. If your shoes feature adjustable tension springs, turn the rear screw clockwise to increase release tension or counter-clockwise to make it easier to exit, tailoring the feel to your preference.

AD

Final Testing and Calibration

After tightening, grab the shoe and attempt to flex the front of the sole upward to ensure the bolts are not protruding and compromising the integrity of the material. Mount the shoe on the pedal and clip in, then perform a few slow circles to confirm the release mechanism is smooth. Listen for any scraping sounds, which indicate that the cleat is too far forward and rubbing against the edge of the pedal, requiring a slight backward adjustment.

Cleat position explained: how to setup & replace cycling cleats | BikeRadar
Cleat position explained: how to setup & replace cycling cleats | BikeRadar
Understanding Clipless Pedals – Installing Cleats On Shoes
Understanding Clipless Pedals – Installing Cleats On Shoes
Types of Cycling Cleats For Every Bike Explained
Types of Cycling Cleats For Every Bike Explained
How To Clean Your Cycling Shoes - Eat More Rabbit Food
How To Clean Your Cycling Shoes - Eat More Rabbit Food
A do-it-yourself guide to fitting cycling cleats - CyclingTips — Escape Collective
A do-it-yourself guide to fitting cycling cleats - CyclingTips — Escape Collective
Cleat position explained: how to setup & replace cycling cleats | BikeRadar
Cleat position explained: how to setup & replace cycling cleats | BikeRadar

Maintenance Tips to Extend Longevity

To get the most out of your investment, treat the metal threads with a light coating of waterproof grease every few changes to prevent seizing. Avoid using excessive force when removing the shoes; if the pedal feels stuck, apply penetrating oil and let it sit rather than brute forcing it. Regularly check the bolts after the first few rides, as they often settle and require a slight retight to maintain the perfect balance of security and float.

If You're Indoor Cycling, Pay Attention to How You're Setting Up Your Shoes
If You're Indoor Cycling, Pay Attention to How You're Setting Up Your Shoes
How To Make Your Cycling Cleats Last Longer
How To Make Your Cycling Cleats Last Longer
How to Install SPD Clips on Cycle Shoes : Indoor Cycling
How to Install SPD Clips on Cycle Shoes : Indoor Cycling
Are Your Cycling Cleats Set Up Correctly? Here’s How to Check
Are Your Cycling Cleats Set Up Correctly? Here’s How to Check
how to clean white road cycling shoes
how to clean white road cycling shoes
Cleat position explained: how to setup & replace cycling cleats | BikeRadar
Cleat position explained: how to setup & replace cycling cleats | BikeRadar
How To Use Clip-In Pedals & Cleats | Clipless Tips For Beginners
How To Use Clip-In Pedals & Cleats | Clipless Tips For Beginners
When should you replace cycling cleats?
When should you replace cycling cleats?
How to Use SM-SH41 Cleat Adapters
How to Use SM-SH41 Cleat Adapters
Wellgo road SPD-SL to SPD converter. Use your road shoes at the spinning class
Wellgo road SPD-SL to SPD converter. Use your road shoes at the spinning class
How to Set Up your Cleats - BikeFitTuesdays
How to Set Up your Cleats - BikeFitTuesdays
How to Maintain and Repair Cycling Shoes
How to Maintain and Repair Cycling Shoes
How to Attach Spd Cleats to Shoes - 8 Easy Steps
How to Attach Spd Cleats to Shoes - 8 Easy Steps
How to Clean & Disinfect Used Cycling Shoes – Budget Cycling
How to Clean & Disinfect Used Cycling Shoes – Budget Cycling
AD