How to Wash Cleats in Washing Machine: The Ultimate Guide
For the dedicated athlete, the state of your gear is just as important as your performance. Cleats are designed to provide maximum traction and support, but they are also notorious for collecting grass, mud, and debris. While the question of whether to machine wash footwear often sparks debate, it is entirely possible to clean cleats in a washing machine without causing damage, provided you follow the correct protocol. This guide will walk you through the precise steps to restore your studs and mesh safely.
Before you even think about pressing start, preparation is the most critical factor in successfully cleaning cleats in a washing machine. The primary goal here is to protect the integrity of the materials and the functionality of the shoe. You must remove any loose debris and take precautions to prevent the aggressive tumbling from deforming the upper or destroying the structure. Skipping these preparatory steps is the fastest way to ruin a good pair of boots.
Preparing Your Cleats for the Wash
Step 1: Remove the Insoles and Laces
Never throw the entire cleat into the machine without modification. Start by taking out the removable insoles or footbeds. These components are typically made of a softer foam that can absorb excessive water, leading to a long drying time and potential odor retention. Set them aside to be cleaned separately, usually by hand with a mild detergent. Next, remove the laces. While some modern synthetic laces can survive a wash, removing them ensures a more thorough cleaning of the shoe eyelets and prevents them from getting tangled in the machine's agitator.
Step 2: Clear Out Loose Debris
Turn the cleats upside down and bang them together to dislodge any large chunks of dried grass or mud. Use a stiff-bristled brush or an old toothbrush to scrub out the treads of the cleats. The objective is to remove as much solid debris as possible before the washing cycle. If you skip this step, the mud will turn into a gritty paste during the spin cycle, potentially scratching the surface of the cleats or clogging your drain filter.
Step 3: Protect the Leather and Surfaces
If your cleats are made of leather or nubuck, you must condition them after the wash to prevent the agitator from drying out the material and causing cracks. Apply a leather conditioner roughly 30 minutes before you plan to run the cycle. For the mesh and synthetic portions, consider placing the shoes inside mesh laundry bags. While not always necessary, this provides an extra layer of protection against snagging and maintains the shape of the shoe during the tumble.
The Washing Machine Process
Once the preparation is complete, you can move to the washing phase. The settings you choose will determine the success of the cleaning and the preservation of the cleats.
| Setting | Recommendation | Reason |
|---|---|---|
| Water Temperature | Cold Water | Hot water can cause glue failure and shorten the life of the shoe. |
| Cycle Type | Gentle or Delicate | Reduces the mechanical stress on the materials and structure. |
| Additives | Detergent Only | Avoid bleach at all costs, as it will discolor the materials. Skip the fabric softener, as it coats the fibers and reduces breathability. |
Place the cleats in the machine alongside old towels or jeans. The towels act as buffers, helping to balance the load and prevent the hard rubber of the cleats from hitting the interior of the drum too violently. Run the cycle. You will hear a distinct rattling noise, but if you prepared the shoes correctly, they should withstand the motion.
Drying: The Make-or-Break Phase
The washing cycle is usually the least damaging part; the drying process is where most people go wrong. Using a high-heat dryer is the number one way to destroy a pair of cleats, as the intense heat can melt the glue holding the sole to the upper.
The Air-Dry Method
The safest method is to air dry the cleats. After the wash cycle ends, remove them immediately. Use old towels to absorb excess moisture from the exterior and the insoles. Reshape the upper if it has wrinkled and stuff the toe box with dry paper towels to help maintain the structure as they dry. Place the cleats in a well-ventilated area out of direct sunlight. Direct sun can fade the colors of the synthetic materials. Depending on the humidity, this process can take 12 to 24 hours.
Using the Dryer (With Caution)
If you absolutely must use a dryer, proceed with extreme caution. Ensure the cleats are only slightly damp before placing them in the machine. Add a couple of dry towels to the load to create a buffer. Most importantly, select the "Air Fluff" or "No Heat" setting if your dryer offers it. The tumbling motion is fine, but the heat is the enemy. Never run them on a standard heat cycle.
Final Maintenance and Odor Control
Once the cleats are completely dry, the process is not quite finished. You need to address the aftermath of the cleaning and ensure the next time you use them, they are fresh.
Reviving the Traction
After the washing and drying process, the rubber outsole might look clean, but the traction can feel slightly altered. Use the soft-bristled brush again to clean the cleats thoroughly. Test the grip on a dry surface. If the cleats feel smooth, you may need to use a simple trick to restore traction: dampen the soles and rub them on a rough concrete surface. This helps to re-establish the friction pattern on the bottom of the shoe.
Dealing with Persistent Odors
Even with a perfect wash, moisture can lead to bacterial growth that causes bad smells. To combat this, sprinkle a mixture of baking soda and cornstarch inside the dry cleats before storing them. This absorbs moisture and neutralizes odors naturally. Alternatively, consider using specialized UV sanitizing devices that kill bacteria without introducing additional moisture into the shoe.
By adhering to these steps, you can confidently clean cleats in a washing machine, saving time and ensuring your equipment remains in top condition for the next match. The key is respect for the materials—treat the process with care, and your boots will reward you with performance and longevity.